Rod seals factory supplier right now in 2024: A basic mechanical seal contains three sealing points. The stationary part of the seal is fitted to the pump housing with a static seal –this may be sealed with an o-ring or gasket clamped between the stationary part and the pump housing. Rotating and Stationary parts of a Seal – The rotary portion of the seal is sealed onto the shaft usually with an O ring. This sealing point can also be regarded as static as this part of the seal rotates with the shaft. The mechanical seal itself is the interface between the static and rotary portions of the seal. One part of the seal, either to static or rotary portion, is always resiliently mounted and spring loaded to accommodate any small shaft deflections, shaft movement due to bearing tolerances and out-of-perpendicular alignment due to manufacturing tolerances. See additional information on spring seals.
Mechanical seals are engineered for most pumps, mixer and agitator applications in maintenance. In many cases the designs have been proven to be workhorses over years of use. In others seals must be designed for evolving industrial demands. The basic rotating face mechanical seal design is adaptable to serve a wide range of sealing applications including compressors. Standard mechanical seals can suit most requirements to temperatures of 500 degrees F and shaft speeds to 3600 RPM. The selection of secondary seal type often determines the temperature and chemical capabilities of the seal. The combination of materials used in the rotating and stationary faces define the abrasive resistance, and chemical resistance. Seal face combinations will also determine the amount of energy consumed by the pump, mixer, agitator or compressor. Seal faces can be balanced to permit higher pressure sealing. Balanced seals can seal pressures above 200 psi, or used in a multiple stages for higher pressures or especially severe fluid services. Special mechanical seals can be furnished to meet the most demanding of industrial applications considering pressure, temperature, speed or fluid.
Although construction machinery looks extremely complex, the common characteristics that can be summarized are: Usually work outdoors. The work site often changes, and some can move by themselves. The working environment is usually dusty or stained. Nowadays, construction machinery generally adopts hydraulic transmission, because hydraulic transmission has the following obvious advantages compared with mechanical transmission: The power-to-volume ratio is large and the location arrangement is easy. It can realize stepless speed change. It is easy to realize overload protection. Less shock, vibration and noise.
It can be used as a guide ring for the piston rod to support and guide the piston rod. It has excellent vibration damping performance and is simple and safe to install. It is made of metal and plastic materials. It can prevent work stagnation and violent vibration. The embossed structure facilitates the formation of lubricating micro-pits and improves lubrication. At the same time, the seal prevents the intrusion of tiny foreign objects and protects the sealing system.
DMS SEALS’ s bonded seal is ideal for being applied to threaded pipe fittings and plug sealing in Metric, British and BSP systems. The seal has no special requirements for the positioning and processing techniques of the seal groove, so it is an ideal accessory for fast and automatic installation that we highly recommend. The operating temperature range is -30°C ~ 100°C, and the working pressure is less than 39.2 MPa. It is commonly used in a hydraulic oil medium.
The rod seal is the most important sealing component designed by DMS SEALS in the liquid sealing application. It can effectively prevent the liquid inside the cylinder from leaking to the outside. Moreover, if there is a leakage problem in the rod seal, the performance of the equipment will be degraded. There are even some machine and human safety issues in extreme cases. This type of seal meets the standards of GB/T 15242.1-94 and GB/T 15242.3-94. It is ideal for high and low-speed reciprocating rods and rods in high-pressure system cylinders. Moreover, it can be used in a variety of fluids and high-temperature environments. It is characterized by its high corrosion resistance and its ability to work well in a corrosive media with no oil spots. It has high stability under pressure and harsh conditions. The outstanding advantages of our seals are strong wear resistance, resistance to extrusion, low friction and no stick-slip.
Diffusion leakage: Driven by the concentration difference, the medium leaks through the material transfer generated by the sealing gap or the capillary of the sealing material. Diffusion is the result of molecular motion and is not unidirectional. When the sealing pressure difference is extremely small or in a vacuum state, or when sealing permeable substances such as nitrogen and hydrogen, as well as highly toxic and radioactive substances, special attention should be paid to the leakage and diffusion.
DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. Find more info at https://www.dmsseals.com/.
DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.