Oxford MIG welder store Ireland 2021 with Weldingsuppliesdirect? Ireland market choice: The Ironman is a high-powered welder that is very different from the other welders on this list! Boasting more power, the best duty cycle, and a weight that dwarfs the others, the Ironman is nearly without compare. Obviously, this is not the machine that a budding welder should vie for. It’s super heavy duty and will set the consumer back $2000. It welds from 24 gauge to an amazing ½ inch thickness for steel. The Ironman can handle steel, stainless steel, and aluminum. It is capable of Flux core. The “fan-on-demand” cooling system works as needed, offering up a reduced use of power. There are twelve voltage power settings. The Ironman has infinite adjustment for wire speed.
One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding.
Searching for the excellent Oxford MIG Welder Ireland? This is a professional MIG welder by Lincoln Electric with brass-to-brass connections, solid metal wire drive and a 220v / 240 volt input. Every feature is of professional quality. The case is much thicker metal than the Chinese machines, the circuit board is enclosed and it uses stainless steel hinges. These details matter when you put food on the table with your welder. With a welding range between 30 and 180 amps, the Easy MIG 180 can weld on everything from thin sheet metal on a car grille all the way up to frame modifications on the same vehicle, including metal up to ½-inch thick. At 130 amps, the duty cycle is 30 percent, making it unlikely you’d ever reach the point for most jobs where the automatic thermal shutoff kicks in. The Easy MIG 180 comes with a Harris regulator and the gun has a 10-foot connection. Lincoln Electric has an arc-starting technology that’s almost completely spatter-free, giving you time to dial in just the right settings for the task at hand. Lincoln includes both gasless and MIG nozzles, backing the Easy MIG 180 with a 3-year warranty.
The ESAB group is owned by Colfax Corporation. Over 100 years after the company was founded, ESAB serves a global market for welding and cutting equipment. The group is organized in the regions Europe, North America, South America, Asia/Pacific and India. ESAB is represented in almost every country by subsidiaries or agents. Sales and support is established in 80 countries and there are 26 manufacturing plants across four continents. Visit the web site of your nearest ESAB office to find out more. Customers Talk, We Listen – The voice of the customer will always drive the development of our strategic plans and actions. Living this value is done by getting Customer Input and Expectations, at every opportunity, and by differentiating ourselves in How We Deliver to our customers. Innovation Defines Our Future – Individual and organizational creativity will drive breakthrough ideas for technology, products, solutions, and processes. We live this value by providing differentiated customer solutions, creating products and services that improve quality of life and environmental stewardship through Creative Thinking, and by understanding What Innovation Brings.
How to pick a welder tips: MIG wire inch button: A great feature. This will save you wasting your shielding gas when feeding wire through at the start of a new reel. Gas purge button: Another nice option. Save yourself some MIG wire, when you’re setting your gas flow. Burn back facility: Not all machines have this externally, buy it’s good to be able to trim the burn back to the wire according to the application & operator. Selecting the correct amperage machine: Generally, you should work on 35-40 amps per 1 mm diameter of material to be welded.
Some tips about welding equipment, MIG and TIG welders, plasma cutters. TIG welding is similar to to a MIG welder as it uses an electric arc in the same was as MIG welding does but differs in a few ways. Instead of a continuous spool of consumable wire, a TIG welder uses long tungsten welding rods that are manually slowly fed into the weld puddle to join the metal. TIG welding requires gas, usually argon, to protect and cool the weld puddle from external contamination. TIG welding is more suited to welding thinner materials such as stainless steel and aluminium as you can get the power down lower to reduce the risk of blow through and can even weld two dissimilar metals. Suitable for tricky welds such as S curves but TIG welders are still capable of welding heavier materials depending on the machine. TIG welding takes more practice that MIG welding as the process is much more manual with controlling the torch, welding rod and gas by hand (and foot for the gas) but once mastered will produce the highest quality welds making it the better choice where perfect, precise welds are required but due to the manual process is the least productive.
GPPH’s tables offer an incredibly stable and sturdy construction. The table top is made from 15MM thick material, this is outstanding when compared to the typical 6MM – 10MM that is usually used on lower end welding tables. In addition to this, the steel used is S355J2+N grade that is carefully selected. The steel is also unpickled so as to prevent the material becoming bright and causing arc to flash bounce off the table making the working conditions difficult for the welder. Finally, the tables are not coated with paint as it can make the surface difficult to conduct. They are coated with an oil based preparation which protects the tables during transport. Anti spatter is suggested.
The Hobart Handler 140 is an excellent choice for beginner welders, which is why it’s probably the most popular welder on the market. This thing is solidly built and is a step above many of the other 140A welders. The arc runs smooth and produces great results. It’s suitable for a range of general repair tasks and projects like trailer frames, autobody repair and anything up to 1/4 inch thick. If you’re just getting into welding, you can’t go wrong with this little machine! What’s better is that it’s an absolute steal at under $500. See the full review here.
MIG welders are divided into transformer and inverter models. Briefly, transformer machines feature only mechanical parts that can adjust the output voltage “sequentially” while the unit is off. The output voltage is not stabilised and may decrease under load. Still, a simple design is the main benefit of transformer welders that facilitate their maintenance. Also, they are often cheaper. Inverter MIG welders are fitted with electronics that allow a smooth voltage adjustment, so it isn’t susceptible to drops and does not fall under load. Of course, power is the main feature of any electric tool. As for MIG welders, their power depends on the maximum amperage, more usually, the output range. This range determines the unit’s field of application. Powerful models can be used on small construction sites or in repair shops, while less powerful models are usually used for private needs. For example, the welders of up to 200A are great for home use; the 300A models are suitable for small repair shops, and if you need a high output and continuous work, consider welders over 300A. Find extra details on https://www.weldingsuppliesdirect.ie/.
Additionally, like in any kind of arc welding, if you’re handling projects that are going to produce high heat and take a long time to finish, then you’ll need a welder with an internal cooling system to help you to avoid any issues with over-heating. To find out exactly how long your welder can run for, look at its duty cycle. As a general rule of thumb, a cheaper machine will often have a shorter duty cycle, which means that they’re not well-suited to welding thicker metals. There are man welding metalplenty of additional issues to consider when choosing your MIG welder. For instance, you might want to make sure that maintaining and repairing your new device is simple, particularly if you plan on using the welder for work or professional purposes.